Advanced Measuring Instruments Certification - AMI 3: Height Measuring Tools Exam Prep
Free practice questions

Free AMI Practice Questions

10 exam-style questions with answers and explanations, straight from our 1,030-question bank. Tap an answer to check yourself. When you're ready, take the scored version in the free practice test.

Start the free practice test → ★★★★★4.9/5 from 2,400+ candidates · No signup

These 10 free AMI questions are organized by exam domain, so you can see how each part of the Advanced Measuring Instruments Certification - AMI 3: Height Measuring Tools blueprint is tested. Reveal the answer and explanation under each question.

Domain 1: Measuring-Instrument Safety

Question 1

A setup height must be checked inside a powered fixture. The cycle is stopped, but a hydraulic clamp remains pressurized and could move into the technician's hands. Access requires entering the clamp's travel path. What must be established before positioning the measuring tool?

Show answer & explanation

Correct answer: A - Verified energy isolation and control of stored energy under the authorized procedure.

Domain 2: Height-Measuring Tool Design, Features, Sizes and Variations

Question 2

An inspection plan requires measuring a shoulder 365 mm above its datum. The gage must have a display increment no larger than 0.005 mm and a specified maximum error magnitude no greater than 0.015 mm. All candidates have current calibration and suitable contact access. Which specification meets all three requirements?

Show answer & explanation

Correct answer: D - Range 0-600 mm; increment 0.002 mm; maximum error magnitude 0.012 mm.

Question 3

A shoulder can be reached with either a short rigid contact arm or a longer one on the same height gage. Consider a small carriage rotation in the vertical plane of the arm, with scale behavior unchanged. What advantage does the smaller horizontal contact offset provide?

Show answer & explanation

Correct answer: B - It reduces the vertical displacement caused by the same carriage rotation.

Domain 3: Calibration and Field Checks

Question 4

A supervisor questions a calibration invoice because the technician made no adjustments to the height gage. The technician used calibrated standards, documented errors and uncertainties at the required heights, and supplied the relationship for correcting indications. The work was performed in the shop. Which explanation resolves the disagreement?

Show answer & explanation

Correct answer: A - Calibration can establish the measurement relationship without changing the instrument.

Question 5

A shop starts using a 0-300 mm height gage for shoulders between 240 and 280 mm. Its existing morning check consists of zero and a 50 mm reference. Calibration is current, but the pre-use check is being revised for the new work. Which revision provides the most relevant additional evidence?

Show answer & explanation

Correct answer: A - Add suitable assigned reference heights across the 240-280 mm working region.

Question 6

The required height-gage checks pass at 08:00 and 10:00. At 12:00, a required upper-range point fails again after cleaning and reseating; no satisfactory check was recorded after 10:00. The control plan requires review of acceptance decisions since the last satisfactory check. With the gage removed from use, which work is the initial review population?

Show answer & explanation

Correct answer: C - Parts accepted with that gage after the 10:00 check.

Domain 4: Tool Application, Accurate Measurement and Maintenance

Question 7

A bracket gives closely grouped height readings while it remains on the surface plate. Lifting and reseating it produces a different group of readings each time. Repeated approaches to a clean height master remain consistent, and the gage returns to its original zero. Where should the inspector look first?

Show answer & explanation

Correct answer: B - At the bracket's datum face and seating, checking for burrs or trapped debris.

Question 8

During a spacer inspection, the zero of a metric vernier lies between 46 and 47 mm on the main scale. Vernier line 17 coincides with a main-scale line, and the least count is 0.02 mm. The approved method accepts indicated heights from 46.25 to 46.45 mm, with no additional correction. Which inspection entry is correct?

Show answer & explanation

Correct answer: C - 46.34 mm; accept within the limits.

Question 9

With an electronic height gage in relative mode, an inspector sets zero on an upper ledge and then contacts a lower ledge without changing the probe or datum. The display reads -2.350 mm. In this setup, the minus sign means that:

Show answer & explanation

Correct answer: D - The lower ledge lies 2.350 mm below the ledge used to set zero.

Question 10

A bracket rests on 10.000 mm parallels during inspection. Its drawing dimensions a step from lower datum ledge B to upper ledge C. Using one unchanged plate zero, the inspector records B at 24.180 mm and C at 57.420 mm. What dimension belongs in the step-height record?

Show answer & explanation

Correct answer: B - 33.240 mm, from the difference between the two ledge readings.

That's 10 of 1,030

The full bank has 1,020 more AMI questions with explanations.

Continue in the free practice test →

View plans